BASIC SERIES INTRODUCTION

The Nextion Basic Series offers 2.4”, 2.8“ 3.2”, 3.5”, 4.3”, 5.0”, 7.0” HMI display size options for you.

You can develop the HMI GUI project via the free Nextion Editor software, the easy Drag-and-Drop components and simple ASCII text based instructions will dramatically reduce your HMI project development workloads.

The Nextion solution is the best balance HMI solution between cost and benefit with low and decreased learning curve.

READ MORE
NEXTION BASIC HMI DISPLAY
MODEL NAMENX3224T024NX3224T028NX4024T032NX4832T035NX4827T043NX8048T050NX8048T070
Size2.4″2.8″3.2″3.5″4.3″5.0″7.0″
Resolution320*240320*240400*240480*320480*272800*480800*480
Touch PanelRTPRTPRTPRTPRTPRTPRTP
Color65536655366553665536655366553665536
Flash4 MB4 MB4 MB16 MB16 MB16 MB16 MB
RAM3584 Byte3584 Byte3584 Byte3584 Byte3584 Byte3584 Byte3584 Byte
MCU48 MHz48 MHz48 MHz48 MHz48 MHz48 MHz48 MHz
EEPROM
GPIOs
RTC
EnclosureNoNoNoNoNoNoNo
SKUIM150416002IM150416004IM150416005IM150918001IM150416003IM150416006IM150416007
DatasheetClickClickClickClickClickClickClick
Price$22.9$25.4$32.4$39.9$54.9$71.9$89.9
icoBUY NOWBUY NOWBUY NOWBUY NOWBUY NOWBUY NOWBUY NOW

Notes: Nextion product numbering rules , eg. NX8048T070

NX – Nextion
80 – Horizontal resolution: 22-220 32-320 40-400 48-480 80-800 10-1024
48 – Vertical resolution: 24-240 27-272 48-480 60-600

T – Series model: T=Basic series, K=Enhanced series, P=Intelligent series
070- Display size: ”070″ means 7.0″
All Basic Series products are resistive touch panel type

ACCESSORIES
nextion_pro

IN THE BOX

NexMIDI*1
XH2.54 4P wire*2

NEXTION MIDI I/O INTERFACE

Two 4-pin XH connectors for 5V power supply, TX, RX and GND allow this interface to be easily daisy-chained between either a power supply / USB to TTL serial adapter like the Nextion Foca Max, or any MCU (Arduino, etc.) on one side (J1) and a Nextion HMI display on the other side (J2). The on-board switch SW1 allows to select between 2 modes:

* PRGM: RX + TX signals are directly routed from J1 to J2 which allows to program the device on J2 by the device on J1 while the MIDI interface is idle.
* MIDI I/O: RX + TX signals from the device on J2 are converted and linked to the MIDI IN and MIDI OUT 5-pin DIN sockets.

NEXTION MICRO SD EXTENDER

1. Feel hard to reach the micro SD card slot?
2. Have to disassemble the product enclosure for the HMI project update?
3. Other extension tools are not working properly?

The Nextion Micro SD card extender helps you to access the SD card slot of the Nextion HMI display more conveniently. It supports the FAT32 Micro SD card as well as all series of Nextion HMI displays compatibilities.

nextion_pro

IN THE BOX

Micro SD card extender*1

nextion_pro

IN THE BOX

Foca Max*1
USB cable*1
XH2.54 4P wire*1

FOCA MAX- USB TO TTL CONVERTER BOARD

Foca Max is a USB to TTL serial converter board with 5.5V2A output. it integrates a high power and energy-efficient DC-DC chip of TPS54331 for a wide voltage input with small voltage ripple. For USB to TTL conversion, the Foca Max can be power supplied by USB only or USB together with external DC 8-26V, The USB and external DC power supplies are isolated by using a diode (SS34) to avoid the current backflowed between them.

Note: as for the Nextion HMI display size less than 4.3”, you can only use the USB for power supply, size large than 4.3”, a external DC 8-26V for power supply is recommended.